|Published (Last):||2 November 2016|
|PDF File Size:||10.63 Mb|
|ePub File Size:||12.26 Mb|
|Price:||Free* [*Free Regsitration Required]|
Quick Links. See also: Owner's Manual. Table of Contents. This manual should be considered a permanent part of the motorcycle.
This publication includes the latest production information available. Honda Motor Co. No part of this publication may be reproduced without written. The vehicle pictured in this owner's manual may not match your actual. Page 2 Honda motorcycle. Page 5: Motorcycle Safety Motorcycle Safety This section contains important information for safe riding of your motorcycle. Please read this section carefully. Safety Guidelines Page 6: Safety Guidelines Safety Guidelines Safety Guidelines that you and your passenger are both wearing an approved motorcycle helmet and protective Follow these guidelines to ensure your safety: apparel.
Ride slowly and cautiously. Carbon monoxide gas is toxic. Your motorcycle may have suffered damage Breathing it can cause that is not immediately apparent. Have your unconsciousness and even kill you. In the interest of safety, take the meanings. Some labels warn you of potential hazards that could cause serious motorcycle to be serviced only by your dealer. Battery produce explosive gas that can cause explosion.
Hot coolant will scald you. Relief pressure valve begins to open at 1. Do not heat. Use surface, park so that the motorcycle cannot engine braking with intermittent use of the move or fall over. Page 18 Riding Precautions 3. Slowly lean the motorcycle to the left until its Refuelling and Fuel Guidelines weight rests on the side stand.
Follow these guidelines to protect the engine 4. Turn the handlebars fully to the left. Doing so can make it unsafe. Excessive engine speed can adversely affect engine life. Page 24 Fuel gauge Remaining fuel when only 1st E segment starts flashing: approximately 3.
Press and hold to advance the hour fast. Press button. Goes off if the ignition key has the correct coding. Page 29 Switches Engine stop switch Should normally remain in the position. In an emergency, switch to the OFF position to stop the engine. Start button Headlight turns off when operating the starter motor.
Hazard switch Horn button Switchable when the ignition switch is ON. LOCK Locks steering. Page Starting The Engine Starting the Engine Start your engine using the following Make sure the engine stop switch is in the position. Turn the ignition switch to the ON position. Shift the transmission to Neutral indicator comes on.
Page Shifting Gears Shifting Gears Your motorcycle transmission has six forward gears in a one-down, five-up shift pattern. If you put the motorcycle in gear with the side stand down, the engine will shut off. Page 33 Refuelling Opening the Fuel Fill Cap Fuel fill cap Filler neck plate Open the lock cover, insert the ignition key, Ignition key Fuel level max and turn it clockwise to open the cap.
Fuel filler opening Closing the Fuel Fill Cap After refuelling, push the fuel fill cap closed until it locks. Page Storage Compartment Storage Compartment Helmet holders, a helmet set wire in the tool kit , a tool kit, and document bag are located under the rear seat.
There is also space to store a U-shaped lock. Tool kit U-shaped lock Helmet set wire Helmet holders Document bag Importance of Maintenance Page Importance Of Maintenance Importance of Maintenance Importance of Maintenance Maintenance Safety Keeping your motorcycle well-maintained is Always read the maintenance instructions absolutely essential to your safety and to before you begin each task, and make sure that protect your investment, obtain maximum you have the tools, parts, and skills required.
Your dealer meets all road test your motorcycle after each periodic of these requirements. Keep an accurate maintenance is carried out. Page 38 : Inspect clean, adjust, lubricate, or replace if necessary you have the necessary tools and are mechanically skilled.
In the interest of safety, have your motorcycle serviced by your dealer. Page 40 : Inspect clean, adjust, lubricate, or replace if necessary you have the necessary tools and are mechanically skilled. You do not have to check the battery hydrogen gas during normal electrolyte level or add distilled water. Clean the operation. Brake fluid can damage plastic and painted surfaces. Wipe up spills immediately and wash thoroughly.
Inspect the tyres for cuts, slits, or cracks NOTICE that exposes fabric or Using coolant not specified for aluminium engines or cords, or nails or ordinary tap water can cause corrosion. If they become visible, replace the tyres immediately. Riding on tyres that are excessively For safe riding, you should replace the tyres worn or improperly inflated can cause when the minimum tread depth is reached.
Genuine balance weights or equivalents after the tyre is installed. Page Tool Kit Tool kit The tool kit is stored under the rear seat. Pull the rear corners of the front seat up, then remove the mounting bolts. Pull the front seat back and up. Insert the tab into the recess.
Insert the ignition key into the seat lock. Turn it clockwise, then pull the rear seat Prongs Rear seat forward and up. Insert the prongs into the seat hook and guide hooks. Insert the clip into the hole. The clip must be removed to remove the 2.
Push the pin in. Remove the pin by a Phillips screwdriver. Remove the front seat. Unhook the rubber strap. Disconnect the negative terminal and Positive terminal remove the battery lead.
Negative terminal 4. If the engine is cold, idle the engine for 3 to 5 minutes. Turn the ignition switch OFF, stop the engine and wait 2 to 3 minutes. Place your motorcycle in an upright Oil level position on a firm, level surface.
Remove the oil fill cap. Add the recommended oil until it reaches the upper level mark. Use a new Honda Genuine oil filter or Discard the oil and oil filter at an equivalent specified for your model. Apply a thin coat of engine oil to the Check the oil level. Check that there are no oil leaks.
Install a new oil filter and tighten. Page Coolant Coolant Checking the Coolant If the coolant level is dropping noticeably or the reserve tank is empty, you likely have a 1. Place your motorcycle on a firm, level serious leak.
Have your motorcycle inspected surface. Hold your motorcycle in an upright position. Place your motorcycle in an upright lever and pedal freeplay becomes excessive, position on a firm, level surface. Check the condition of the brake pad groove Always inspect both left and right wear indicators. Front The pads need to be replaced if a Rear Inspect the brake pads from the brake pad is worn to the bottom of the Page Side Stand Side Stand 4.
Start the engine, pull the clutch lever in, and shift the transmission into gear. Lower the side stand all the way.
Download Manual: 2008 Honda CBR600RR — Owner's Manual
Owner's Manuals. Online Viewer. Manual Description If the Combined ABS indicator operates in one of the following ways, your brakes will continue to work as a conventional system, but without the Combined ABS function. Reduce your speed and have your motorcycle inspected by your dealer as soon as possible. Indicator does not come on when the ignition switch is in the ON position. Indicator comes on or starts flashing while riding. You turn the rear wheel while your motorcycle is lifted off the ground.
2014 Honda CBR600RR — Owner's Manual