If you found this page, you probably have a problem and you need a user manual for the device DigiTech RP Be sure to check that it is the user manual to exactly the device that you are looking for. A user manualDigiTech RP50 is taken from the manufacturer, a DigiTech company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device DigiTech RP50 directly. You can view the user manualDigiTech RP50 directly online or save and store it on your computer. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with DigiTech RP
|Published (Last):||16 January 2014|
|PDF File Size:||12.93 Mb|
|ePub File Size:||16.79 Mb|
|Price:||Free* [*Free Regsitration Required]|
Quick Links. Table of Contents. Page 2 Warning For your protection, please read the following: Water and Moisture: Appliances should not be used near water e.
Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. Page 3 Vice-President of Engineering S. Page 4: Warranty 7. The foregoing is in lieu of all other warranties, expressed or implied, and Digitech neither assumes nor authorizes any person to assume any obligation or liability in connection with the sale of this product.
In no event shall Digitech or its dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond their control. It is your key to unlocking the potential within the RP Footswitches - These 2 Footswitches are used to select presets, access the Tuner, or bypass the RP The Up Footswitch increments, and the Down Footswitch decrements through the presets.
Pressing both Footswitches simultaneously bypasses the selected preset. Pressing and holding both Footswitches Page 7 Each effect LED will light to indicate which effect you are editing 4. When the Drums feature is active, the Drums LED lights and the selected drum pattern plays continuously.
Page 8: Rear Panel This jack also can be used as a headphone jack. Page 9: Making Connections Before connecting the RP50, make sure that the power to your amplifier is turned off, and the power to the RP50 is disconnected. There is not a power switch on the RP Page Applying Power EQ response on most amps, this would be 0 or 5 on the tone controls.
The battery compartment is located on the bottom of the RP The following diagram shows how to install the batteries. Page Play Mode Factory Presets. In Play mode, use the Up and Down Footswitches to access Enter the Tuner by pressing and holding both Footswitches simultaneously.
The tu briefly displays indicating that you are in Tuner mode. To begin tuning, play a note on your guitar the neck pickup usually works best. The RP50 lets you create your own presets, or fine tune existing Presets to suit your needs. When creating or editing a sound, you must start with a User or Factory Preset. The Edit buttons move you through the Effect modules. The LEDs light indicating which effect group is selected. Each effect has multiple settings to select from. The Value buttons are used to change the value for the selected effect.
The following steps outline how to store changes to a preset or copy a preset to a different location: 1. Each effect within the RP50 can be programmed to suit your personal application. Understanding how these effects alter the sound helps you achieve the sound you are looking for. The EQ in the RP50 is similar to the tone knobs on an amplifier. Values cut the level of each band, 5 is flat no cut or boost , and values boost the level of each band.
The delayed signal is modulated in and out of tune and then mixed back with the original signal to create a thicker sound, and stereo image. Use the Value buttons to select one of the nine Chorus settings. Flange F1-f9 A Flanger uses the same principle as a Chorus but uses a shorter delay time and adds Page Rotary Speaker Vibrato b1-b9 A Vibrato effect modulates the pitch of the incoming signal at an even rate.
Use the Value buttons to select one of the nine Vibrato settings. Rotary Speaker r1-r9 Rotary Speaker is an emulation of a device that included a spinning horn and woofer. The rotation of these two speakers produces an interesting combination of sound panning from side to side with a slight pitch change produced from the speed of the sound coming towards, and then going away from the listener. Page Pitch Shift of effect as if two guitars were playing the same part together.
Use the Value buttons to select one of the nine Detuner settings. Pitch Shift H1-H9 The Pitch Shifting copies the incoming signal, and shifts the pitch of the copy to a different note. The shifted note is mixed back with the original signal sounding as if two guitars were playing different notes. There are two different parameters used to program the delay, Delay Variation and Time. Any passive volume pedal can be used as an expression pedal with the RP Page Factory Reset All such data will be lost forever!
The procedure for performing a Factory Reset is as follows: 1. Disconnect the power supply from the RP50 AC Power or unplug the guitar from the input jack battery power. Print page 1 Print document 29 pages. Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL.
DigiTech RP50 User Manual
Digitech RP50 User Manual
RP50 Manual Digi Tech Multi Effects Owner’s Manuals
DigiTech RP50 Music Pedal User Manual